Chapter 210: : The Magic Board

With the release of water near Zhuang, and the dispatch of a real old fish 腩 team by Xucheng Tunnel, Niushan Woodenware Factory finally got the precious sugar maple.
They knew that they had fallen a lot behind. After getting the wood, they didn't dare to delay for a minute, and immediately convened everyone to start studying this fast wood.
Because the time is very tight, it is too late to dry before processing. The factory manager Hu intends to take two steps to break the huge block of wood and cut it into two blocks.
Take one piece to dry, and start processing one piece now, try various processing methods, and try drying after processing.
And this kind of more precious wood cannot naturally be cut casually. Some precious woods, even those with a price higher than gold, are slightly more depleted in the production process, which can cause people to die.
Plant Manager Hu didn't dare to entrust him, he went into battle, measured the size of the wood, and then drew a cutting line. Then they cleaned up the band saw and replaced it with imported ultra-thin and ultra-thin saws. The master craftsman with the best craftsmanship came out in person and began to break the ground.
The band saw rotates at a high speed. Even some traditional hardwoods are as fragile as foam on this band saw. The master has set up the guide rails, ruler and stopper. Both hands firmly hold the wood. Moved closer to the wood.
As soon as the band saw touched the wood, a "squeak" sound was heard.
"Oh, this is not the right voice!" The master subconsciously dragged back, dragged the wood back, then turned off the band saw, and then saw it on the saw blade, and suddenly sweated: "Fortunately, close early! "
"What's the matter?" Director Hu also came forward, and saw that the original fine sawtooth had missing teeth, which cost thousands of dollars. The imported saw blade, which can be sawed even by steel, was almost worn. draw.
"What's wrong? Did we get the wrong saw blade?"
"It's not wrong, it was the imported saw blade that we bought last time. That's right." The master turned his head to look at the wood, and saw that a white line was cut out from the wood, embedded in the white line With one small tooth.
"This isn't flattened, it's ... stuck!"
What kind of wood can seize this ultra-high hardness sawtooth?
多 How tough is the fiber of this thing?
"Let's ... look in another direction?" Master Fu wiped a cold sweat, and said, "This time, let's try along the wood grain?"
Just now, I was going to cut the wood horizontally and cut it vertically. I didn't expect the wood grain to be so strong.
"This may cost more ..."
"It's better than not being able to cut. If you can cut into plates, you can use a laser cutter." Master Fu said.
Director Wu Hu thought about it and nodded.
Now he couldn't care about making the best use of the material. He crossed the wood, changed a band saw, and started the machine again.
The sound of "squeak!" Was louder than before.
"This sound is right." Master Fu Wenwen pushed forward with both hands, but the more he pushed forward, the more wrong his voice was. From the beginning it squeaked into a buzzing sound.
After two centimeters, the saw blade was caught in the wood!
"Water spray!"
"The water is spraying ..."
"What's going on? How could it get stuck?"
Finally, the wood was detached from the band saw. The band saw was already black, it was rubbing carbonized wood, and the master was at a loss.
The vertical wood grain will be cut off by teeth, and it will be caught along the wood grain. What can I do?
The factory director Hu Hu moved forward and suddenly wondered, "Well, what about the white line just now?"
Just now, when the vertical wood grain was cut, the band saw cut a white line on the wood.
此时 At this point, the white line had faded to almost invisible.
Master Fu, unbelievably, reached out and touched the position of the white line. He only touched a few broken teeth that were stuck inside the band saw before, and small triangular teeth were sticking at the fingertips.
The white line was completely invisible.
"This ... how is that possible?" Master Fu and Director Hu glanced at each other, and quickly looked at the saw mark just a centimeter deep along the wood grain.
They saw that the saw mark was recovering at a speed that was visible to the naked eye, and the little silver light at this time seemed to become particularly bright, showing a silver bright line at the saw mark.
After the saw marks were fully recovered, the silvery lights of the stars spread out, and the wood became the original look again.
Flat, smooth, boxy, beautiful texture.
But the hairs of Master Fu and Chang Hu both felt that they were going to stand up.
"This ... this wood will not be alive." Master Fu said.
"Even if it is ... even a tree that is alive, it is impossible to grow so fast!" Chang said in his heart that the wood pieces he had seen in his life were 10,000 without 10,000, but never seen Which piece of wood is so exaggerated!
到底 What the is this?
Isn't this just a piece of wood? How could he heal himself?
Is this actually Cybertron's cube?
Or what magical alien creature?
No, this is impossible.
How can this kind of wood that can't be cut open and heal itself can be processed into floor?
"Shouldn't it be for us!" Director Hu almost fell to the table.
"No, no ... other companies, there will always be a way, go and ask, how do other companies process this wood?"
. Said the factory director Hu.
Although it is only a small factory, after all, I have been soaking in the wood processing industry for so many years, and some people still have contacts.
Soon they contacted several companies that also received orders ~ EbookFREE.me ~ I heard that the factory director Hu inquired about the wood. At the beginning, several companies were sloppy: "This is a trade secret, Lao Hu, If I told you, it would be wrong. "
"Don't come to those imaginary, can't you not cut the wood?"
With that said, the other party couldn't hold up, and suddenly complained: "We imported seven or eight saw blades that were scrapped and the motor was almost burnt out. After changing the methods, I sent myself and the factory manager to enlarge Saw it, why can't I cut this wood, and you say the wood that can't be cut, how can I process it? "
There is also a manufacturer saying: "Our boss has a familiar metal processing factory. He intends to take this wood and go to the metal processing factory to try a metal cutting machine. We are waiting for news."
After a while, he again said, "Old Chen of the metal processing factory almost beat our boss out, saying that our woodwork had broken their blades ..."
Most of the metal cutting is by milling. The high-speed rotating blade is almost entangled with flexible wood fibers into cocoons.
It wasn't just the factory director Hu who inquired about the news. Other people were helpless about this piece of wood, and they were inquiring about each other. When they heard that others were okay with this piece of wood, one or two were aggressive, what can I do?
"By the way ... how did this wood cut into the first place?" Director Hu suddenly said, can't this wood grow like this at first!
For a long time, the director of Wuhu called Deng Yali's phone.